Properties
Application
The heated gas sampling probes series PSG Process Probe ATEX 180 are used for continuous extractive gas analysis. They enable trouble-free representative sampling of hot predominantly dust and water vapour loaded gases. Typical applications are measurements and monitoring in explosive plant components
Technology
The intelligent design with optimum gas guidance enables the filtration of sample gas at the outer filtration surface of 212cm2, allowing service periods of up to 2 years (depending on the dust concentration). If it is necessary to change the filter, the arrowed corkscrew mechanism allows this to be done quickly and conveniently in just a few steps without tools and without disassembling the connected heated sample gas line. The full-surface tight-fitting aluminum heating element with the two self-regulating heating cartridges ensures homogeneous heating of the entire PSG Process Probe ATEX 180to 180°C even at the lowest ambient temperatures. State 07 / 2022. Subject to change
Functions
Due to the largest filtration surface dust will always be separated reliably in the PSG Process Probe ATEX 180. The heating concept prevents water vapour condensation in order to reliably prevent blocking of the filter. For elevated dust concentrations of up to 40g/m3 resp. 280g/m3 the PSG Plus Probe ATEX 180 can be equipped with an ultimate effective single or dual stage back purging with tubing of 12mm outer diameter. In this way filter chamber (single stage) as well as filter element are back purged thoroughly and low-maintenance operation is ensured.
You may also be interested in
Sampling Tubes in various materials and length for different applications
6 mm / 8 mm Pressure Reduction Valve for Protection of the Sampling System
Self limiting Probe with 180°C holding temperature for use in IP 65 housing and explosion proof for ATEX Zone 1 II 2G Ex d IIC T3 and IEcEX
Self regulating Sample Line up to 120°C holding temperature, cut-to-length with PTFE / PFA or stainless steel tubes, fully certified for ATEX Zone 1: II 2G Ex IIC
Self regulating Sample Line up to 120°C holding temperature, cut-to-length with PTFE / PFA or stainless steel tubes, fully certified for ATEX Zone 1: II 2G Ex IIB
Controlled Sample Line up to 180°C holding temperature, cut-to-length with PTFE / PFA or stainless steel tubes, heating cable certified for ATEX Zone 1: II 2G Ex IIC und IEcEX
Compressor Cooler for Process Measurement (outlet dew point optimized), 1-4 Gas Path, Heat Exchanger in various Materials, flow rates up to 500 l/h for ATEX EX II 2G Ex px de [ai] IIC T4 Gb
High Performance Compressor Cooler (outlet dew point optimized) with 1-4 Gas Path, Heat Exchanger in various Materials and flow rates up to 500 l/h
Compressor Cooler for Process Measurement (outlet dew point optimized), 1-2 Gas Path, Heat Exchanger in various Materials, flow rates up to 350 l/h for Atex-zone 2 (II 3G Ex nA nC T4 Gc)
Self limiting mobile Probe heated up to 180°C holding temperature for temporary CEMS
Controlled Probe up to 200°C holding temperature and double back purge for Process measurement with high dust load
Controlled DeNOx Probe up to 315°C holding temperature for SCR and SNCR applications with separator vessel for Ammonia salts
Self limiting Probe with 90 °C holding temperature with explosion proof for ATEX Zone 1 II 2G Ex d IIC T3 Gb
Controlled Probe up to 315°C holding temperature for Process and Emission measurement with high dust load
Controlled Sample Line up to 180°C holding temperature, cut-to-length with PTFE / PFA or stainless steel tubes, heating cable certified for ATEX Zone 1: II 2G Ex IIC und IEcEX
Controlled Sample Line up to 150°C holding temperature, cut-to-length with PTFE / PFA or stainless steel tubes, heating cable certified for ATEX Zone 1: II 2G Ex IIC und IEcEX
Self-regulating or regulated duo probe up to 250°C holding temperature for simultaneous sampling from 2 outlets at low to medium dust loadings
Self regulating or controlled Probe heated up to 200°C holding temperature for CEMS and low to medium dust load
Temperature controlled Heated Sample Tubes for 180°C Holding Temperature
Corrosion resistant PTFE diaphragm sample gas pump for low maintenance operation and compact design 7.5 l/min. flow rate, Motor IP66, Pump IP55 for ATEX Ex II 2G Ex h IIB+H2 T4 Gb
PID Temperature Controller for PSG Gas Sampling Probes and Heated Lines (tabletop device)